Printable View
Hi, just upgraded mah hardware since i really had junk in my pc >P
but anyway i got
P5Q Pro motherboard http://www.asus.com/products.aspx?l1...69&modelmenu=1
And an Intel Core 2 duo E8400 processor
me like >)
Some editing, i noticed the last few days that the heat of the core is staying the same, core 1 at 43-45, and core 2 at 35-37, i got this badboy cooling it down , i touched the heatsink its hardly warm at all so is that good or what ?
It means your have a really uneven surface on the HS or the screw's/ clips are not properly adjusted.
Or theres too much/too little thermal paste and not in the right area's.
Nice upgrade, great CPU for gaming. I need a new CPU, I think my E6400 is bottlenecking my GTX280 somewhat. But i'm gonna wait for Nehalem anyway.
nope, everythings greatly attached, and we put thermal grease on it so great cooling ...
weird that one core is so badly above the other as the cpu usage wont affect that stupidly probably the program reporting this is bad.
As long as it doesn't go over 60C load you'll be fine :D.
im using Coretemp 0.99, when i go into a game, the heat gets closer to each other...
I wouldn't worry TBH, it takes time for the thermal paste to set properly anyway.
It is common that the curvature of the heatsink or processor is uneven, causing those varying temperatures between the 2 cores. For some reason, some seem to be a lot worse than others. I have got a few games open as well a tonne of programs, and my Q6600 (@ 3.0GHz) is running at 36,33,33,35 from core0 to core3.
If you are worried about the varying temps (which I would be if I wanted to overclock), it may be worth lapping the heatsink and CPU with a variety of sandpaper. In fact, would you mind telling me how you applied the thermal paste, and what type it is? You should have followed the arctic silver technique which says put a very thin line vertically across the cores - instructions. If you manually spread it with a card or your finger, that may well be why the temps are so different.
Other than that, nice setup :).
yeah thermal paste was even all on the processor, but i went in a game but either of the cores goes over 44, but heatsink is bit well warmer now, and i do not overclock, simply because im not experienced with that and i dont think i need it
but i must say the heatsink with the fan is fucking huge
well it says Tj. Max is 105Quote:
Originally Posted by Phantom
what the hell is TJ????
I don't know, ignore it.
ok now i think something is wrong with coretemp cuz i just started my pc and core 1 is at 43 and core 2 at 28 dang, last night they both went up to 48
Its the program your using, stop using it and just read the bios temp's which are going to be more reliable than the joke your using now.
CoreTemp is actually a very good piece of software, but it might be worth trying RealTemp.
Ok tested REAL Temp
At the moment,
Realtemp says 33 and 27
Coretemp says 43 and 37
So dangit???
EDIT: also i noticed that coretemp says 2999.70mhz (330.30 x 9)
and RealTemp says 1999.80mhz (330.30 x 6)
so is Coretemp or Realtemp really that off????
EDIT: well its the same deal with both programs just that realtemp always shows 10degrees lower
There is a thing on quadcores called smartstep that underclock's the processor in realtime that changes the clock like that but I usually disable it.
my room is like spain, TWO HOT, and coretemp says 43, and realtemp says 33 GAAAARGH!!
Ah yes my rooms always "TWO" hot :D
Buy one get one free on Michelin Girls this winter!Quote:
Originally Posted by ez64